搜索:

您所在的位置:纺机网 >> 青岛即墨市大成印染机械厂 >> GR202-5KG~600KG高温拉链染色机

产品推荐

产品分类

友情链接

联系方式

  • 联系人:张福胜
  • 邮 箱:info@dachengqd.com
  • 地 址:青岛即墨市通济区西流峰
  • 手 机:013808994677
  • 电 话:0532-82529788
  • 传 真:0532-82529777
分享到:

GR202-5KG~600KG高温拉链染色机

发布时间:2007-02-09

安装与调试
*布置安装位置时,除考虑机器本身机械安装的空间外,还要考虑染机周围的场地,是否能满足装缸、出缸、布放纱笼等要求以及是否有利于今后保养工作的进行。
*机器可按下法找平:气动打开缸盖、在缸口处,十字交叉水平尺检验水平,最后紧固地脚螺栓。
*排液口和卸压管的下方,均应开有地沟,使废液沿着地沟顺利排出,避免溅溢地面,腐蚀机器支架,地沟方位用户根据现场自行决定。
*调试前应检查各部位的螺栓(特别是泵底架的螺栓或调节丝杆)是否紧固,带有联轴器的泵一定要使电机与泵轴同心。
*电气设备及压缩空气控制线路的安装位置,均由使用单位根据厂房具体情况自行决定,但应方便操作,不影响纱笼的搬运。(注意:电缆切勿靠近热源)
操作运转
操作前的准备工作:
*检查各气动阀和电气位置,确使它们在装设位置与控制柜上各按钮开关一一对应。并使泵的转向正确。
*用肥皂液苏打溶液或其它适宜的洗涤剂对机器进行彻底清洗。
*为避免可能的残留污物给试验原料造成污斑,为此试验时最好先染深色,后染浅色。
*染槽内通入所需要软水,将装有被染物的染笼吊入染槽后加热到40-50℃煮炼十分钟,取出染笼排液。
操作转注意事项:
禁止在受压状态下启盖或常压状态下闭盖排液。
主泵与辅泵绝不允许在缺水情况下启动,泵在运转中如发生异常声响或其它故障时,应立即停车检修。
特别注意:
请严格遵守当地劳动部门或锅炉压力容器安全主管单位的规章制度和法规:并接受上述部门的监督和检查。
严禁在80℃以上开启锅盖或各管口,以免发生事故。

Installation and adjustment
*When arranging installation positions,besides considering the self mechanical installation space of the equipment,the surrounding site of dyeing machine shall also be considered so as to ensure the cylinder lilling ,cylineer discharging and sarong layort,etc work wioo be favorable to the furure maintenance.
*The machine can be levelve acfording to following mathod:Open the cylinder coer pneumatically.
Place the horizontal ruler in cross directions on the cylinder opening to inspect the levelness.Finally fix the anchor bolts.
*The sewer shall be arranged rnder the liquor drainage outlet and pressure relief pipe so thet the waste liquor wil be easily discharged along the sewer to avoid splashing to grund,which will be corrosive to the bracket of maching.The sewer location shall be determined by customer according to the site conditions.
*Inspect bolts in every part before adjustment for fastness(especially the bolts and adjusting leading screws of pump bracket).The motor shall be concentric with pump shaft for pump with coupler.
*The installation ot elecric equipment and compressed air control circuilt shal be deteimined by customer according to actual conditions of workshop .However it shall be convenient for the operation withort lffecting the teanspoutation of sarongs.(Note:Keep cable away from the heat source).
Operation
Preparation before operation
*Inspect the location of each pneumatic valve and electric device so as to ensure thet their installation position will be corresponding to each button switch on the control cabinet and ensure the correct pump rotation.
*Do thorough cleaning for the machine with soap bath,soda solution and other suitable wasbing abents.
*In order to avoid bloch on test materials by probable remaining dirt,it is better to dyt deep color first and then dye weak color in the test.
*Fill in required slft water inside the dye bexk and then hoist de cage containing materials to be dyed into the dye beck.Jeat to about 40-50℃and boil for ten minutes.Tske ort the dye cage and discharge teh liquor.
Notes to in operation:
*It is strictly prohibit to open the cover undrr pressurizing comdition or close to discharge liquor vnder normal pressure condition.
*The main pump and auxiliary pump can mot be started when lacking of water.If there is any abnormal noise or other faults in the operation of punp,it shall be stopped immediately for inspection.
Special motes
*Please observe strictly the laws and regulationg stipulated by local labour department or the safety authorityfor pressure containers of boiler,and accept the supervision and inspection by the abovementionsd departments.
*Strictly forbid opening the cover of boiler or respective mauth of pipe in oder to avoid accident.